Place the material evenly when the centrifuge is in use

Before the operation of the Shanghai Xinzhuang centrifuge, the power should be cut off and the centrifuge brake should be loosened first. The drum can be turned by hand to see if there is any bite. Check for other parts of the area for looseness and abnormality. Turn on the power and start the drive in a clockwise direction (usually about 40-60 seconds from standstill to normal operation). Usually, each equipment must be empty for about 3 hours after it arrives at the factory. It can work without abnormal conditions. Place the material as evenly as possible. Must be operated by a person, the capacity must not exceed the rated amount. Never overspeed the machine to avoid affecting the life of the machine. After the machine is started, if there is an abnormal situation, it must be stopped for inspection and repaired if necessary. The centrifuge is running at high speed, so it is not possible to touch the drum with the body to prevent accidents. The mesh size of the filter cloth should be determined according to the size of the solid phase particles of the separated material, otherwise the separation effect will be affected. In addition, when installing the filter cloth, insert the filter cloth sealing ring into the drum sealing groove to prevent the material from running in. In order to ensure the normal operation of the centrifuge, please rotate the parts every 6 months. At the same time, check the running lubrication condition of the bearing, whether there is wear phenomenon; whether the components in the brake device are worn or not, and replace it severely; the bearing cover has no oil leakage. After the machine is used, it should be cleaned and kept clean. Do not separate the non-preservative centrifuge from the highly corrosive materials; in addition, strictly follow the equipment requirements and regulations, non-explosion-proof centrifuges should not be used in flammable or explosive places.
"Surge"

Centrifuges in refrigeration centrifugal units often experience "surge". The principle of a refrigerating centrifugal compressor is to compress a large molecular weight refrigerant by a high-speed movement to a small space for compression, and then condense by cooling. The energy adjustment mode of the centrifugal chiller is to adjust the compression ratio by adjusting the angle of the high-speed rotating guide vane. When the cooling capacity is decreased, the work done by the guide vane is reduced, and the pressure of the compressed gas is similar to that of the suction compressor. Gas backflow produces mechanical forcing vibrations. (Also called "surge") Surge can cause damage to mechanical parts. Centrifuge Development Centrifuge is a device for separating samples. It is widely used in biomedicine, petrochemical, agricultural, food hygiene and other fields. It uses the difference in precipitation speed of different substances in the centrifugal force field to realize the analysis and separation of samples. Since the advent of the centrifuge, the progress of low speed, adjustment and overspeed has been mainly reflected in the centrifugal equipment and centrifugal technology, and the two complement each other. From the perspective of rotational speed, the desktop centrifuge is basically in the category of low-speed, high-speed centrifuges. Therefore, it has the technical characteristics of low-speed and high-speed centrifuges. Its structure is mainly composed of motor drive system, refrigeration system, mechanical system, rotor and system control. The composition is only a small size and capacity compared to the floor-standing centrifuge. The development of universal benchtop centrifuges has blurred the boundaries of low-speed, high-speed, micro- and high-capacity centrifuges. Numerous rotors provide a wide range of applications for researchers and become the preferred model for research laboratories.
Shanghai Xinzhuang Instrument Co., Ltd. is a technologically innovative high-tech enterprise based in Shanghai and radiating the whole country. The company has first-class technicians and a good team of technicians, with advanced technology and strong development strength. Since its establishment, the company has The service is recognized by the majority of customers and has a good reputation. The company adheres to the business philosophy of "integrity, professionalism, innovation and growth" to provide customers with meticulous service.

Lipstick is a cosmetic product containing pigments, oils, waxes, and emollients that apply color, texture, and protection to the lips.

Many colors and types of lipstick exist. Some lipsticks are also lip balms, to add color and hydration.

Although the name originally applied to the baton (stick) of material, within a tubular container, usually around 10mm in diameter and 50mm in length the term now generally relates to the material itself, regardless of method of application.

Lip Stick

Lip Stick,Makeup Powder,Matte Liquid Lipstick,Glimmer Liquid Lipstick

HENAN BON INDUSTRIAL(COSMETIC) CO.,LTD , https://www.boncosmetic.com